How to Setup the Wavlink WiFi Extender?

Wavlink Wifi Extender Setup

Wavlink WiFi extender setup can be accomplished in a variety of ways. Congratulations on your recent purchase of a new Wavlink wireless range extender. You’re probably wondering how to go about the Wavlink setup and installation. You don’t have to worry about that because we have a lot of information on how to complete the Wavlink WiFi range extender setup using various techniques and how to troubleshoot any issues that may arise on your device. 

First and foremost, we will go over the prerequisites for performing the Wavlink WiFi extender setup using the default web address wifi.wavlink.com. So let us begin with this installation guide. 

Steps for Wavlink setup

After reviewing the requirements, we recommend that you prepare for the Wavlink extender setup and installation. As previously stated, there are numerous techniques for configuring your device; you can find all of them here:

Manual Method

  1. First of all, connect your new range extender nearby the cordless router.
  2. Switch on your gadget and attach your PC or smart device to its network.
  3. You may be asked to go into the WiFi password. Use the default password.
  4. After that, open an internet browser on your laptop or smart device.
  5. Enter the default internet address wifi.wavlink.com in the address bar.
  6. Press Enter. You will certainly get to the Wavlink WiFi extender setup web page.
  7. Adhere to the on-screen directions to pair your device with the router’s network.
  8. Settle the cordless settings of your extender.
  9. Click Save/Apply in the long run.
  10. Finally, the Wavlink setup will certainly be finished.

WPS Method

This is one of one of the most easy techniques of going about the Wavlink WiFi extender setup. Although it is a simple method, you won’t have the ability to set up the settings based on your requirement. Kindly follow the actions listed below;

  1. Attach your extender to the power supply near by the router.
  2. After that, locate the WPS switch on your router and the extender.
  3. See to it your router supports the WPS method of setting up the extender.
  4. Press the WPS switch on your extender.
  5. Within one or two minutes, press the WPS button on your router.
  6. Allow both gadgets pair up.
  7. It will certainly take a few minutes to finalize the configuration.
  8. Ultimately, the Wavlink setup will be finished with no problem.

Troubleshooting Common Issues

Right here are several of the most reliable pointers and techniques that will help you eliminate the Wavlink WiFi extender setup issues:

  1. Firstly, reboot your device.
  2. If you were not able to set up your device, you require to reset it.
  3. Press and hold the reset button for 10 seconds.
  4. Once the gadget resets to the initial setups, you can re-attempt to establish your gadget.
  5. Currently, make sure the device is plugged into a power outlet that is devoid of any concerns.
  6. After that, connect your computer system to the extender’s network.
  7. Afterwards, most likely to the ap.setup and also you will certainly get to the Wavlink extender configuration web page.
  8. Make certain you adhere to the actions really carefully.
  9. Go into the appropriate Wi-fi password of your router’s network.
  10. See to it you do not shut off the device in the middle of the setup procedure.
  11. Lastly, the gadget will certainly be set up successfully.
  12. Finally, the Wavlink WiFi extender setup will be completed. 

Conclusion

This page was all about the Wavlink WiFi extendwer setup using the default web address wifi.wavlink.com. We discussed the two main methods to go about the Wavlink setup process. You can either set up your device using the default web address wifi.wavlink.com or you can use the WPS method to configure your device. 

Going through the initial configuration of your Wavlink wireless range extender is super easy. You must follow the instructions very carefully in order to avoid any issues. If you experience any problems with your device or you have any doubts, feel free to talk to our support team for more help. 

FAQs

How do I connect my Wavlink to WiFi?

You can connect your Wavlink wifi extender either through the wifi.wavlink.com or the WPS method. We suggest that you use the default web address to set up your device. You just need to pair your extender with the router’s network. After that, the extender will be set up successful. 

How do I change my WiFi password with Wavlink?

To change the WiFi password of your Wavlink wireless range extender, you need to login to the device using wifi.wavlink.com. After that, go to the Wireless page and follow the on-screen instructions to change the WiFi password. 

How do I reset my Wavlink router password?

You can reset your router’s password using the reset button. Press and hold the reset button for at least 10 seconds. After that, release the button and wait for a few seconds. At last, the extender will restore the factory default settings. 

Scroll to Top