A Madpower WiFi extender is a wise purchase for your home or place of business. All that’s left to do is configure it using the re.madpower.home address. However, you must correctly configure your Madpower WiFi extender if you want to get the most out of your gadget. It’s crucial to set up the extender correctly because a poor setup can lead to serious problems with the extender. Additionally, the ideal design will remove any dead zones from your home. The Madpower WiFi extender manual can be used to assist with setup.
Don’t worry, though, if you find the handbook to be too long to read. You can access the most comprehensive Madpower WiFi extender setup instructions at http //re.madpower.home. Continue reading in order to properly understand the entire process!
Requirements for Madpower WiFi Extender Setup
Here are a few things that you need before you go about the setup and installation of your new device. Refer to the points below:
- A router in place
- The WiFi extension from Madpower
- Website access to re.madpower.home
- A smartphone or computer
Now, you can go ahead with the Madpower WiFi extender setup.
Methods to setup the Madpower WiFi Extender
There are two approaches you can use to set up a Madpower WiFi extender. The WPS button or the web address re.madpower.home can be used to configure the extender. The steps for using these techniques are as follows:
Method 1: Madpower WiFi extender setup via Web GUI
- You can go about the setup for the Madpower WiFi Extender at http://re.madpower.home
- Start by connecting the WiFi extender to a power outlet close to your router.
- Make sure the power LED is solidly on and on.
- Connect your device now to the network of the extender.
- You have the option of connecting wirelessly or using an Ethernet cable.
- In the address bar, type http //re.madpower.home after the connection has been established.
- The extender’s configuration page will now show up on the screen.
- After that, you can set up your extender by following the instructions.
- To connect, type the network and password for the router here.
- The extender will reboot to implement the adjustments after the setup is complete.
- Finally, you can unhook the extender and move it to a location with poor coverage.
- Make that the LED light is on and that it is plugged into a reliable power source.
- You can now reconnect to the WiFi network of the extender.
Method 2: Madpower WiFi extender setup via WPS
- Setup for Madpower WiFi Extender through the WPS Button is super easy.
- The router and extender should first be turned on and placed in the same room.
- On both the extender and the router, look for the WPS button.
- Press and hold the WPS button on the router for a few seconds until the WPS light begins to blink.
- After that, within two minutes, push the WPS button on the extender.
- As soon as the WPS light starts blinking, you can release the WPS button.
- A successful connection is indicated when the WPS light stabilizes.
- The extender can then be moved to the desired spot.
Common Issues with Madpower Wifi Extender and how to fix
There can be several common issues that may come up on your device while going about the Madpower WiFi extender setup and installation.
- Madpower extender setup fails
- Can’t access the Madpower WiFi extender setup wizard
- Extender not working after the setup
- Can’t configure the extender settings
- Extender won’t connect to the router’s network
How to fix the common Madpower extender issues?
In this section, we will walk you through certain steps to help you fix the common issues that may come up on your extender. Follow the steps below:
- The configuration will fail if either of the two devices is turned Off.
- Make sure to plug both devices into an active electrical socket as a result.
- Try connecting them to a different outlet if the present one isn’t working.
- You must connect your device to the extender’s network in order to configure the extender.
- You cannot configure the extender without a connection.
- Check the cable if you are establishing a connection via an Ethernet cable.
- Make sure you are establishing a connection to the correct network, which has the SSID “Madpower_Extender.”
- The configuration page can only be accessed using the IP address and http //re.madpower.home.
- Make sure you are using the right IP address if you are using it.
- The incorrect IP address prevents access to the setup page.
These steps will help you resolve the setup issues, be sure you correctly try these techniques. Make sure to consult the manual for your Madpower WiFi extension before doing any troubleshooting steps.
Conclusion
We hope you now understand how to configure the Madpower WiFi extender setup. You can fix any problems you have with your extender by using the methods outlined above. However, you can get in touch with our team if you run across any other problems.